How to Remove Fishing Line from the Reel

To remove the fishing line from a reel, first, make sure that it is not attached to any lures or hooks. If so, you will need to disconnect them before proceeding. Then remove the spool of the line from the reel and cut off the old line with scissors if necessary.

If you have an open-face spinning reel, pull out the bail arm and use your fingers to unwind all of the remaining lines from around the spool. For a closed-face spinning reel, turn its handle counterclockwise until all of the old fishing lines are removed. Once you have taken off as much as possible by hand, use pliers or needle nose tweezers to take off any remaining pieces of fishing line stuck in small crevices or grooves on either side of your reel’s spool.

Finally, add a new fresh fishing line back onto your reel according to manufacturer instructions before heading out for another day on the water!

  • Unwind the fishing line from the reel: Begin by winding the excess line around your hand and slowly unwind it from the reel, taking care to not further entangle it in the process
  • Use scissors or a knife to cut off any knots: If you encounter any knots while unwinding, use scissors or a sharp knife to carefully cut them away so they don’t get tangled in other parts of the reel
  • Detangle remaining line with tweezers: After removing all visible knots, use tweezers to detangle any remaining pieces of fishing line that may be stuck in small crevices and hard-to-reach places on your reel
  • Clean out debris with a soft brush: Once you have removed as much of the fishing line as possible, use a soft brush (such as an old toothbrush) to sweep away any dirt or debris that has collected inside your reel’s spool housing area over time
  • Apply lubricant sparingly: To help reduce friction between different components of your reel, apply just enough lubricant oil onto moving parts such as gears and bearings for optimal performance without causing damage due to over-lubrication
How to Remove Fishing Line from the Reel


How Do You Remove a Line Spool from a Spinning Reel?

Removing a line spool from a spinning reel is fairly straightforward. First, you need to locate the bail wire arm, which holds the line in place on the spool. Then, open the bail wire arm and manually pull out any excess line that may be wrapped around it.

After that, unscrew or unclip the locking ring or latch located at the base of your reel’s spool so you can remove it completely. Once removed, you can now easily disengage any knots and replace them with a new fishing line before reattaching your spool back into its original place with either screws or clips depending on what type of spinning reel you have.

How Do You Remove Baitcasting Line?

Removing the baitcasting line is a straightforward process that begins by removing the spool from the reel. Then, using needle-nose pliers or your fingers if you have strong enough hands, carefully pull out the line until there are no more loops left on the spool. Next, use scissors to cut off any remaining bits of the line from around the rim and inside of the reel before adding a new line.

To finish up, reattach your spool back onto your reel and start casting again!

How Do You Change the Line on a Fishing Reel?

To change the line on a fishing reel, begin by removing the spool from the reel. Unwind any existing line that is still attached to the spool and remove it. Make sure to tie a knot at one end of your new line, then insert it into the opening in your spool followed by winding it back onto the spool until you have reached desired length or full capacity.

Once complete, secure both ends with an arbor knot and place them back into your reel before heading out to fish.

How to quickly and easily remove fishing line from a reel

Fishing Line Stuck under Reel

When fishing lines become stuck underneath a reel, it can be tricky to remove them. To safely and effectively get rid of the line, use needle-nose pliers to pull out any loose pieces of line that may be tangled around the spool. If there is still some line left in the reel after removing as much as possible with pliers, gently turn the crank while using an old toothbrush or similar tool to scrape away the remaining debris from inside the spool until all of it is removed.

Taking your time during this process will help ensure that you don’t damage either your rod or reel in the process.

How to Unspool Fishing Line

If you are a fisherman, knowing how to unspool fishing lines is essential for successful angling. The first step in properly unspooling your fishing line is to make sure that the spool is securely attached to something sturdy so it doesn’t move when you pull on the line. Then, use your fingers or a pair of pliers to pinch the tag end of the line and gently unwind it from the reel.

Make sure not to let any kinks form in the line as you do this; if needed, keep tension on both ends of the line while pulling it off so that it remains straight and tangle-free. Once all of your fishing lines have been removed from their storage container, clip any excess material and tie it onto an appropriate hook before heading out on your next adventure!

Fishing Line Remover

A fishing line remover is an essential tool for any angler. It removes knots, tangles, and other debris from your fishing line so you can continue to fish without interruption. Fishing line removers are relatively inexpensive and easy to use, making them a great addition to any tackle box.

With the right type of remover, you’ll be able to quickly remove troublesome snags from your line with minimal effort, allowing you to get back out on the water in no time.

How to Take Line off a Baitcaster

Taking the line off of a bait caster is relatively simple. First, attach the reel to an elevated object with something like a belt or strap that can hold it in place. Then, use your index finger and thumb to press down on the spool while you turn the handle until all of the lines have been taken off.

Once done, take out any remaining knots and then re-spool the reel with a new line when ready!


Removing the fishing line from a reel is an important part of maintaining your equipment. It’s essential to be aware of the type and size of line you’re using, as this will determine how it should be removed and what tools will be best suited for the job. You can use scissors or pliers to cut away unnecessary lengths of line, or specialized fishing tools such as a backing plate to help remove tightly wound lines.

With patience and care, you can safely manage any tangled fishing line on your reel without causing damage to either the line or your equipment.

Similar Posts